MEM Series
Our Products / Self-Contained Emergency Lighting / MEM Series
Self-Contained Emergency Light Luminaires
The MEM209CD2 self-contained emergency light has a modern and compact design with special functions not available in other units. It has both a motion and a light sensor to provide maximum functionality for the user for multiple use cases. During power outages the unit will provide illumination using battery power. During normal power conditions, if the surrounding area is dimmer than 5 Lux and the unit detects a person walking by, it will automatically provide illumination using mains power and will turn off automatically after 15 seconds when there is no one left in the area. This extra functionality can be enabled or disabled by the user.
The casing is produced from 1mm thick Electro-Galvanized steel coated with Epoxy powder and special chemicals to prevent any rust from forming.
Technical Specifications
Mode of Operation | Non-Maintained |
Input Voltage | 220 VAC / 50Hz ± 10% |
Output Voltage | 12.8VDC |
LED Lamp Power | 9W Per Bulb |
Color Temperature | Warm White (3000K ± 250K) Daylight (6000K ± 250K) |
Rated Beam Angle | 50Deg, |
Battery Type | Lithium Iron Phosphate (LiFePO4) |
Testing Systems | • Automatic Testing • Manual Testing or Remote Testing |
Charging Mode | 3 Steps Charger System |
Charging Current | 120 mA. |
Charging Time | 10-15 Hrs. |
Backup Time | 2.0 Hrs. |
Housing | Electro-galvanized steel sheet 1mm. thick with epoxy powder coating |
Dimensions (LxWxH) | 165 x 64 x 172 mm. |
Weight | 1.52 Kg. |
IP Rating | 20 |
Features
Bulb
- Highly efficient and super bright LEDs provides maximum brightness while saving on power consumption. It also offers long operational life of more than 50,000 hours.
Battery
-
Lithium Iron Phosphate (LiFePO4) 12.8V-1200mAh (6.4V-1200mAh x 2)
that can provide 2 hours of emergency power
Functions
- The Motion Sensor function can be enabled or disabled.
- A 5-second, 30-minute or 60-minute self-test can be performed on the unit using the remote.
- The 30-minute self-test that the unit will automatically perform every 30 days can be turned on or off.
Circuit Systems
- Controlled by an 8-bit microcontroller circuit.
- An Autoactivation circuit when under voltage occurs.
- A Timer Delay circuit to keep the unit operating for a few more seconds once normal power has returned.
Protection Features
- AC and DC fuse to prevent current overload
- Surge Protection.
Features to Extend Battery Life
- An Innovative 3 Steps Charger
- A Low Voltage Cut-Off to prevent the battery from draining completely
Warning Systems
- An audible alarm will sound twice every 15 seconds to indicate that the battery should be charged.
- An audible alarm will sound once every 15 seconds to indicate that the battery is about to run out of charge.
- An LED will blink 3 times every 15 seconds to indicate that the battery only has less than 30 minutes of charge.
- An LED will blink 4 times every 15 seconds to indicate that there is a problem charging the battery.
Indicators
IR | An infrared receiver |
LED AC. | Indicating input status |
LED Charge/Full | Indicating charging status |
LED MT On | Indicates if the motion sensor function is on |
LDR | Light detector |
LED Test | Indicates if the unit is performing a self-test |
LED Fail | Indicates there is a problem with the battery |
LED Auto Test | LED Auto Test – Indicates if the auto-test is enabled. |
Switch On-Off | Used to turn on or off the unit |
Switch MT On-Off | Used to turn on or off the motion
sensor function |
Switch Test | Used to perform a self-test on
the unit |
MEL Series | Spec Sheets
Model | Lamp (Bulb) | Lamp (Wattage) | Battery Capacity | Back up (hr.) | Length (mm) | Width (mm) | Height (mm) | Weight (kgs.) |
---|---|---|---|---|---|---|---|---|
MEM209CD2 | 2 | 9 | 12V-1.2Ah. | 2.0 | 165 | 64 | 172 | 1.52 |